If this message is not displaying properly, click here to launch your browser.

Livorsi GPS Pulse Antenna

GPS Pulse Antenna

For Use With Any Electric Automotive or Commercial Speedometer
With 8K or 16K Pulse Signal

Convert your electronic automotive speedometer into a GPS speedometer with this GPS Pulse Antenna. The antenna receives GPS satellite signals and outputs the information to 8,000 or 16,000 pulse signal to your existing speedometer. This antenna eliminates connections to the transmission or the need to calibrate to your vehicles tire size.

This fast update antenna receives signals 10Hz (10 per second) driving your speedometer to display your true speed (no pointer lag). This antenna is a stand alone device, which does not require a membership fee for GPS service. The antenna can be mounted under the dash or in an other hidden area as long as you verify the speedometer is working properly before permanently mounting the antenna.

Accuracy and ease of installation makes this GPS Pulse Antenna an affordable solution if you are looking to upgrade to a GPS speedometer system.

  • Outputs 8,000 or 16,000 pulse signal to work with your existing electronic speedometer
  • Eliminates cables to transmission
  • No calibration needed
  • 10Hz update for real time data (10 per second)
  • 2 3/4 in. L x 2 3/8 in. W x 7/8 in. H
  • Operating voltage is 10-32V DC, unit typically consumes < 50Ma at 12V
  • 4 foot harness with ring terminals to connect to threaded #8-32 studs

For more information or to place an order, please call 847.752.2700

Part Number: GPSESQ3

Fuel and Water Level Senders

Suitable for Gas, Diesel and Water

SFW sender

Measurement is done by series of reed switches positioned inside the level tube. A float with built in magnets then triggers the reed relays generating a potential - free resistance with an ohm value that increases or decreases.

The float is the only moving part of the sensor, thereby minimizing potential mechanical failures. All sensors are fully insulated to protect against voltage inside the tank.

  • Available from 4 inches to 36 inches
  • 316 Stainless Steel
  • SAE 5 Hole Pattern
  • 240-33 OHMS
  • Other resistances available upon request
  • Constructed to meet and/or exceed all applicable ISO standards
  • Optional threaded NPT Adapter for screw in applications
  • Sensors are fully insulated to protect against voltage inside the tank
  • Float is the only moving part of the sensor, minimizing mechanical failure

For more information on these senders, click here

News

To request a catalog, click here

Request a Livorsi Automotive Catalog

Request your catalog today!
Email info@livorsi.com with your full name and address. And while your waiting for your catalog to arrive, you can view the catalog online by visiting www.livorsi.com/auto and downloading a PDF.

 SEMA Member
The Number 1 Choice in Performance!
www.livorsi.com/auto
715 Center St.                        Grayslake, IL 60030                        P: 877-548-5900                        F: 847-752-2415

Livorsi and the Livorsi logo are either registered trademarks or trademarks of Livorsi Marine, Inc. in the United States and / or other countries.

© 2011 Livorsi Marine, Inc. All rights reserved.

PLEASE DO NOT REPLY TO THIS MESSAGE. To obtain information on how to contact Livorsi, visit us on the web at: https://livorsi.com/auto, or call 877-548-5900. This is an advertising message from Livorsi Automotive If you would prefer not to receive e-mail like this from Livorsi in the future, please click here to unsubscribe or send an e-mail to livorsi_automotive-unsubscribe@lists.compx.com. Alternatively, you may mail your unsubscribe request to Livorsi Marine at the following address:

UNSUBSCRIBE
Livorsi Automotive
715 Center St.
Grayslake, IL 60030