-
LED indicator main harness – LED2HSA
Select options This product has multiple variants. The options may be chosen on the product pageThis main harness is required for all Livorsi Adjustable LED Position Indicators. It provides power to the indicator, delivers a 5-volt reference signal to your tab or drive sensors, and returns accurate sensor readings for real-time display. In addition to …
-
N2K only LED indicator main harness – LED2HNM30
Add to CartThis harness is required for all Livorsi Adjustable LED Position Indicators using NMEA 2000 exclusively for both input and output. One end connects directly to your NMEA 2000 backbone, while the other features a 12-pin Deutsch connector that interfaces seamlessly with your …
-
LinkUp sensor side harness – GATEWAYVHARNESSBT
Add to CartThis harness goes on the sensor side of the gateway, it connects with an AMP connector and has bullet connectors on the other end.
-
LinkUp LED indicator interface harness for single device – GATEWAYVHARNESS1
Add to CartThis harness is made for setups where you’re using a LinkUp NMEA 2000® gateway with a single-slot Livorsi Marine adjustable LED indicator. Since the LinkUp gateway is programmed using your smartphone, it’s often easier to install it near the dash instead …
-
LinkUp LED indicator interface harness for twin device – GATEWAYVHARNESS2
Add to CartThis harness is specifically for applications when the Link Up NMEA 2000 gateway is used with a two-slot Livorsi Marine adjustable LED indicator. Since the Link Up gateway requires programming via your smartphone, it could be more convenient to mount the …
-
LinkUp NMEA 2000 gateway – GATEWAYV
Add to CartThe LinkUp Gateway makes it easy to connect things like fuel level sensors, trim tabs, rudder angles, and engine data to your boat’s NMEA 2000® system. If you’re adding new electronics or upgrading old wiring, this device helps turn those …
-
NMEA 2000® male terminator – 010-11080-00
Add to CartThis standard male NMEA 2000 light cable connector provides termination resistance for one end of the backbone of the network. Each male or female connector sold separately.
-
NMEA 2000® female terminator – 010-11081-00
Add to CartThis standard female NMEA 2000 light cable connector provides termination resistance for one end of the backbone of the network. Each male or female connector sold separately.
-
T for NMEA 2000 backbone – 010-11078-00
Add to CartAdd components to your NMEA 2000 network by installing our T-connector on your backbone cable. The revised version of this T-connector is offset by 45 degrees compared to the previous version.
-
Power cord for NMEA 2000 backbone – 010-11079-00
Add to CartSupply power to your NMEA 2000 network with our 2 meter (6 ft) power cable.
-
32′ NMEA 2000 backbone cable (10m) – 010-11076-02
Add to CartThis 30 foot long NMEA 2K backbone / drop cable can be used with all Livorsi Vantage View gauges as well as any NMEA 2K compatible devices.
-
13′ NMEA 2000 backbone/drop cable – 010-11076-04
Add to CartThis 13 foot long NMEA 2K backbone / drop cable can be used with all Livorsi Vantage View gauges as well as any NMEA 2K compatible devices.
-
6′ NMEA 2000 backbone / drop cable – 010-11076-00
Add to CartThis 6-foot-long NMEA 2K backbone/drop cable can be used with all Livorsi Vantage View gauges and any NMEA 2K compatible devices.
-
18′ NMEA 2000 backbone cable (6m) – 010-11076-01
Add to CartThis 18 foot long NMEA 2K backbone / drop cable is compatible with all Livorsi Vantage View gauges as well as NMEA 2K compatible devices
About
At Livorsi Marine, we design and manufacture high-performance parts and accessories for all kinds of boats. From weekend cruisers and towboats to military and commercial vessels, our products are built to perform, look sharp, and last in tough marine environments.
Capabilities
Simple things like adding a logo, applying a custom color to design from scratch new products can all be done with the vast resources found at Livorsi Marine.