-
$52.08
Diode kit harness for twin engine throttle – DKH2
Add to CartDiode harness for single switch twin motor trim control.
-
$60.55
Diode kit harness for triple engine throttle – DKH3
Add to CartDiode harness for single switch triple motor trim control
-
$14.20
Four piece diode kit for Livorsi throttles – DK
Add to CartDiodes only, 4-piece kit. A diode is a electronic component that acts like a one-way check valve, Allowing current to flow easily in one direction while blocking it in the opposite direction. This is commonly used when using one control …
-
$26.64
Harness for Livorsi 24 volt analog gauges – DCH24
Add to CartThese factory-assembled harnesses plug into all Livorsi analog gauges. Populated in all 4 of the DT06-4S sockets are the following 24″ long wires:
GREEN WIRE – SIGNAL
BLUE WIRE – LIGHTING
BLACK WIRE – GROUND
VIOLET WIRE – 12V POWER…
-
$15.59
Harness for Livorsi analog gauges – DCH
Add to CartThese factory-assembled harnesses plug into all Livorsi analog gauges. Populated in all 4 of the DT06-4S sockets are the following 24″ long wires:
GREEN WIRE – SIGNAL
BLUE WIRE – LIGHTING
BLACK WIRE – GROUND
VIOLET WIRE – 12V POWER -
$63.29
3 pin, 25’ long Jack plate wire harness with split loom – DC5VWH-201000
Add to CartThis harness is best used for our 5-volt gauges that connect to your 5-volt sensor. An ideal application for this harness is a pressure gauge. This harness is 25’ long, protected in split loom sleeving, and plugs directly into our 2 5/8″ 5-volt …
-
$60.12
6 pin 20’ long jack plate wire harness with heat shrink – DC5VWH-010000
Add to CartThis harness is best used for our 5-volt gauges that connect to the Livorsi marine rotary position sensor. An ideal application for this harness is a rudder or jet pump bucket position indicator. This harness is 20’ long, protected in heat …
-
$54.12
3 pin, 20’ long jack plate wire harness with split loom – DC5VWH-101000
Add to CartThis harness is best used for our 5-volt gauges that connect to your 5-volt sensor. An ideal application for this harness is a pressure gauge. This harness is 20’ long, protected in split loom sleeving, and plugs directly into our 2 5/8″ 5-volt …
-
$184.17
6 pin, 20’ long jack plate wire harness with split loom – DC5VWH-000000
Add to CartThis harness is best used for our 5-volt gauges that connect to the Livorsi marine rotary position sensor. An ideal application for this harness is a rudder or jet pump bucket position indicator. This harness is 20’ long, protected in split …
-
$61.80
Foot throttle harness for PCM engines – CHPCM15
Add to CartThis 15-foot-long harness is best used in airboats. One end plugs into the Livorsi foot throttle, part number EFP, and the other into a Pleasurecraft Marine engine.
-
$99.48
23′ electric throttle and shift harness for PCM engines – CHEECPCM23
Add to CartCHEECIND23 – This 23″ long harness is a plug-and-play solution for any Livorsi EEC side mount throttle and a PCM marine engine with a PCM transmission.
-
$159.89
23′ electric throttle and shift harness for Indmar engines – CHEECIND23
Add to CartThis 23″ long harness is a plug-and-play solution for any Livorsi EEC side-mount throttle and an Indmar marine engine with a Velvet Drive transmission.
-
$30.06
Bob’s Machine jack plate sender adaptor harness – BJPAWH-000000
Add to CartBob’s Machine jack plate sender adaptor harness
-
$117.48
Vantage View Slave Harness for eight gauges with 12″ of wire between gauges – VVSH8L
Add to CartVantage View slave harness are factory assembled using DT06-6S Deutsch connectors that plug into the Vantage View master tachometer and supply power and data to the rest of your gauges. This plug and play system allow for an …
-
$75.56
Vantage View Slave Harness for two gauges with 12″ of wire between gauges – VVSH6L
Add to CartVantage View slave harness are factory assembled using DT06-6S Deutsch connectors that plug into the Vantage View master tachometer and supply power and data to the rest of your gauges. This plug and play system allow for an …
-
$78.59
Vantage View Slave Harness for six gauges with 8″ of wire between gauges – VVSH6S
Add to CartVantage View slave harness are factory assembled using DT06-6S Deutsch connectors that plug into the Vantage View master tachometer and supply power and data to the rest of your gauges. This plug and play system allow for an …
-
$54.44
Vantage View Slave Harness for four gauges with 8″ of wire between gauges – VVSH4S
Add to CartVantage View slave harness are factory assembled using DT06-6S Deutsch connectors that plug into the Vantage View master tachometer and supply power and data to the rest of your gauges. This plug and play system allow for an …
-
$57.24
Vantage View Slave Harness for four gauges with 12″ of wire between gauges – VVSH4L
Add to CartVantage View slave harness are factory assembled using DT06-6S Deutsch connectors that plug into the Vantage View master tachometer and supply power and data to the rest of your gauges. This plug and play system allow for an …
-
$33.34
Vantage View Slave Harness for two gauges with 8″ of wire between gauges – VVSH2S
Add to CartVantage View slave harness are factory assembled using DT06-6S Deutsch connectors that plug into the Vantage View master tachometer and supply power and data to the rest of your gauges. This plug and play system allow for an …
-
$36.28
Vantage View Slave Harness for one gauge with 25″ of wire between gauges – VVSH1XL
Add to CartVantage View slave harness are factory assembled using DT06-6S Deutsch connectors that plug into the Vantage View master tachometer and supply power and data to the rest of your gauges. This plug and play system allow for an …
-
$35.49
Vantage View Slave Harness for two gauges with 12″ of wire between gauges – VVSH2L
Add to CartVantage View slave harness are factory assembled using DT06-6S Deutsch connectors that plug into the Vantage View master tachometer and supply power and data to the rest of your gauges. This plug and play system allow for an …
-
$36.28
Vantage View Slave Harness for one gauge with 12″ of wire between gauges – VVSH1L
Add to CartVantage View slave harness are factory assembled using DT06-6S Deutsch connectors that plug into the Vantage View master tachometer and supply power and data to the rest of your gauges. This plug and play system allow for an …
-
$162.49
7′ long Vantage View Master harness for Mercury Smartcraft gauges – VVMHSC7FT
Add to CartThis 7 foot long master harness is a plug and play solution when adding a Livorsi Vantage View gauge to your Mercury Smartcraft equipped vessel. The 7′ long harness has a 12 pin Deutsch connector on one end and a NMEA 2000® Micro …
-
$38.93
Vantage View wired switch assembly – VVSAW
Add to CartThis factory assembled switch set allows the Vantage View gauge user to scroll through the master gauge LCD screen. Using the mode and selection switch you can scroll to view specific parameters, fault codes or warnings as well as set …
About
At Livorsi Marine, we design and manufacture high-performance parts and accessories for all kinds of boats. From weekend cruisers and towboats to military and commercial vessels, our products are built to perform, look sharp, and last in tough marine environments.
Capabilities
Simple things like adding a logo, applying a custom color to design from scratch new products can all be done with the vast resources found at Livorsi Marine.