-
$16.00
Cut and calibrate service – CCFL
Add to CartIf you would like Livorsi to cut and calibrate your fuel level sender to a specific length, add this part number to your cart. The cut and calibration process can have up to a 2-week lead time.
-
Price range: $43.65 through $128.94
Fuel and water level sender – SFW
Select optionsSFW Fuel/Water level senders are suitable for gas, diesel, and water. Measurement is done by a series of reed switches positioned inside the level tube. A float with built-in magnets then triggers the reed relays, generating a potential-free resistance …
-
$37.68
Water temperature sender 1/2″ NPT – GSWT1/2
Add to CartThis analog temperature sender works specifically with Livorsi analog 100-250° F Water Temperature gauges. This sender connects to the engine block with a 1/2″ NPT thread. When installing the sender for your gauge onto the engine, do NOT use any sealant …
-
$29.74
Water temperature sender 1/8″ NPT – GSWT1/8
Add to CartThis analog temperature sender works specifically with Livorsi analog 100-250° F Water Temperature gauges. This sender connects to the engine block with a 1/8″ NPT thread. When installing the sender for your gauge onto the engine, do NOT use any sealant …
-
$76.73
0-100 PSI oil pressure sender with isolated ground – GSOPI
Add to CartThis analog 0-100 PSI oil pressure sender works specifically with Livorsi analog 0-100 PSI pressure gauge.This sender connects to the engine block with a 1/8″ NPT thread. This sender does not get it’s ground from the engine block, rather it …
-
$106.23
0-60 or 90 PSI fuel pressure sender – GSFP6090
Add to CartThis analog 0-60 or 0-90 PSI fuel pressure sender works specifically with the Livorsi analog 0-60 or 0-90 PSI fuel pressure gauge. This sender connects to the engine block with a 1/8″ NPT thread. When installing the sender for your gauge …
-
$107.13
0 to 15 PSI fuel pressure sender – GSFPWP
Add to CartThis analog 0-15 PSI fuel or water pressure sender works specifically with the Livorsi analog 0-15 PSI fuel pressure gauge. This sender connects to the engine block with a 1/8″ NPT thread. When installing the sender for your gauge onto the …
-
$66.57
0-100 PSI oil pressure sender – GSOP
Add to CartThis analog 0-100 PSI oil pressure sender works specifically with Livorsi analog 0-100 PSI pressure gauge.This sender connects to the engine block with a 1/8″ NPT thread. When installing the sender for your gauge onto the engine, do NOT use …
-
$66.57
0-80 PSI oil pressure sender – GSOP80
Add to CartThis analog 0-80 PSI oil pressure sender works specifically with Livorsi analog 0-80 PSI pressure gauge.This sender connects to the engine block with a 1/8″ NPT thread. When installing the sender for your gauge onto the engine, do NOT use …
-
$185.70
NMEA 0183 1Hz GPS antenna – GPSSQ3
Add to CartThis standard GPS antenna is supplied with ring terminals. These antennas easily connect to all Livorsi analog GPS speedometers. Operating at 1Hz, this unit outputs NMEA 0183 data at 4800 baud, 8 data bits,1 stop bit, no parity (NMEA 0183 standard), or simply put …
-
$225.12
NMEA 0183 10Hz GPS antenna – GPSSQ310X
Add to CartThis standard GPS antenna is supplied with ring terminals. These antennas easily connect to all Livorsi analog GPS speedometers. Operating at 10Hz, this unit outputs NMEA 0183 messages at 38,400 baud, or simply put, updating your speed ten times per second. This …
-
$222.72
NMEA 0183 1Hz GPS antenna for Livorsi Vantage View Gauges – GPSRAQ3VV
Add to CartThis Vantage View GPS antenna is manufactured with Deutsch terminals on the power and ground supply wires and a butt connector on the data signal wire. This antenna easily connects to all Livorsi Vantage View master tachometers for easy installation. …
-
$238.67
NMEA 0183 10Hz GPS 8 and 16k pulse output antenna – GPSESQ3
Add to CartThis unique GPS antenna converts a GPS NMEA 0183 signal to standard automotive speedometer pulse output. There are two settings for this pulse antenna; it can output 8k or 16k pulses per mile, depending on how you wire the antenna to …
-
$233.29
Mechanical cable to 5 volt converter – CBME5VD-000020
Add to CartThe Livorsi CBME5VD converter uses your 33c cable to move the Livorsi Velocity sensor. The sensor has two outputs, output one is programmed for a .5v to 4.5 volt output and sensor two is programmed for 4.5 to .5 volt output. As …
-
$241.63
Programmable Fuel Level Senders 3 Terminal 240-33 ohms – AFLSATL
Select options“Livorsi Marine’s AutoCal fuel level senders feature advanced microcontroller technology and are easy to identify by an “A” in the part number (e.g., AFLS) and the absence of trim or adjust potentiometers on the top. These senders have …
-
Price range: $241.63 through $273.85
Autocal Fuel Level Senders – AFLS
Select optionsLivorsi Marine’s AutoCal fuel level senders feature advanced microcontroller technology and are easy to identify by an “A” in the part number (e.g., AFLS) and the absence of trim or adjust potentiometers on the top. These senders have …
About
At Livorsi Marine, we design and manufacture high-performance parts and accessories for all kinds of boats. From weekend cruisers and towboats to military and commercial vessels, our products are built to perform, look sharp, and last in tough marine environments.
Capabilities
Simple things like adding a logo, applying a custom color to design from scratch new products can all be done with the vast resources found at Livorsi Marine.